A worn chart pinned above a desk, far out of focus, with a notebook and pencil on the desk below in warm lamplight

The conversions a chemistry problem actually uses are the metric prefixes, volume, temperature and pressure, plus the four that move between moles and something measurable: molar mass, the Avogadro constant, molarity, and gas volume. They are grouped below by where in a problem each one happens, each with the condition it carries.

One thing to say before the chart. A conversion chart tells you what a factor is worth. It cannot tell you which factor the problem needs, and that is the decision students actually get stuck on. The method for making it is dimensional analysis, which picks each factor by what has to cancel.

Metric prefixes, which are exact by definition

A prefix is a power of ten, and NIST publishes the set. OpenStax makes the same point: fractional or multiple SI units are named with a prefix on a base unit, and these are always powers of ten. The ones a chemistry course uses:

PrefixSymbolFactor
gigaG10^9
megaM10^6
kilok10^3
decid10^-1
centic10^-2
millim10^-3
microμ10^-6
nanon10^-9
picop10^-12

The condition: none. These are definitions, so a prefix conversion is exact and never limits the significant figures in an answer.

Length, mass and volume

  • 1 m = 100 cm = 1000 mm
  • 1 kg = 1000 g. OpenStax notes that the gram is exactly one thousandth of the mass of the kilogram, which is the unusual case of an SI base unit carrying a prefix in its own name.
  • 1 L = 1 dm^3. OpenStax says the liter is the more common name for the cubic decimeter.
  • 1 mL = 1 cm^3, and 1 L = 1000 mL.

The condition: the volume identities are exact, which is why a lab measurement in cm^3 can be written as mL without a second thought. The one to watch is 1 m^3 = 1000 L rather than 100 L, because a cubed prefix cubes its factor.

Temperature, which is not a conversion factor at all

  • T(K) = T(degrees C) + 273.15
  • T(degrees F) = 1.8 x T(degrees C) + 32

The condition, and it is the important one on this page: these are not ratios and they cannot be canceled against anything. OpenStax explains why. Most units are directly proportional, of the form y = mx, so one ratio converts between them, but the temperature scales do not share a common zero point, which forces the form y = mx + b with an offset.

Practically: a difference of 1 degree Celsius is a difference of 1 K, but no single factor converts a temperature reading between the two scales. You add 273.15, you never multiply. And anything with T in it, which means every gas relationship, needs kelvin before the substitution, not after.

Pressure

From OpenStax, and all of these are for gas problems:

  • 1 atm = 101,325 Pa = 760 torr
  • 1 torr = 1/760 atm, and 1 mmHg is approximately 1 torr
  • 1 bar = 100,000 Pa exactly, which makes 1 bar slightly less than 1 atm
  • 1 kPa = 1000 Pa
  • Air pressure at sea level is roughly 14.7 psi, which is about 1 atm

The condition: the pressure unit you land in has to match the gas constant you are about to use. With pressure in atmospheres, R is 0.08206 L atm per mol per K. With pressure in kilopascals and volume in liters, R is 8.314. Converting a pressure and then using the wrong R undoes the conversion. The ideal gas law page carries both values beside the relationship. Each gas law and the unit that breaks it is laid out in gas laws on one page.

Mass to amount: the conversion every reaction problem starts with

  • n = m / M, and m = n x M, where M is the molar mass in grams per mole

The molar mass is the sum of the standard atomic weights of the atoms in the formula. Those values come from the IUPAC abridged table: H 1.0080, C 12.011, N 14.007, O 15.999, Na 22.990, S 32.06, Cl 35.45, Ca 40.078. Sulfur and chlorine are given to fewer decimal places than the others because their published uncertainties are genuinely larger, not because the table is being casual.

Worked, so the chain is visible: the molar mass of CaCO3 is 40.078 + 12.011 + 3(15.999) = 100.086 g/mol, so 5.00 g is 5.00 / 100.086 = 0.0499570 mol, reported as 0.0500 mol.

The condition: the formula has to be the right one. A molar mass computed for CaCO3 when the substance is Ca(HCO3)2 cancels its units perfectly and is still wrong, which is the failure mode dimensional analysis cannot catch.

Amount to number of particles

  • N = n x N_A, where N_A = 6.02214076 x 10^23 per mole

NIST gives that value as exact, because since the 2019 revision of the SI the mole is defined by fixing it. Courses usually round it to 6.022 x 10^23, which is four significant figures and more than most masses in a textbook problem carry.

The condition: particles means whatever the formula unit is. A mole of CaCl2 contains one Avogadro’s number of formula units and three times that many ions, and the question decides which one it wants.

Amount and solution volume

The condition: molarity is moles of solute per liter of solution, not of solvent. This is the most consequential single condition on the page, because every concentration calculation downstream inherits it. The dilution relation holds because adding solvent does not change the amount of solute, which also tells you when it does not apply: it is not valid across a reaction, only across a dilution.

Volume also has to be in liters before it meets a molarity. A volume in milliliters is the most common reason a concentration answer comes out a thousand times off.

Amount to gas volume

  • V = nRT / P, from the ideal gas law
  • At 273.15 K and 1 atm, one mole of an ideal gas occupies 22.41 L

The condition: kelvin, an R that matches the pressure unit, and behavior close enough to ideal, which OpenStax describes as a reasonable assumption at relatively low pressure and high temperature. Quote the 22.41 L per mole only when the problem is actually at those conditions. At 25 degrees Celsius and 1 atm the molar volume is about 24.5 L instead, and a problem that uses 22.41 L there is off by about eight percent before it starts.

Reading the chart in the order a problem uses it

Most quantitative chemistry problems run the same route, and each arrow on it is one entry above:

mass or volume, into moles, across the balanced equation by the mole ratio, back out of moles into the unit asked for.

The prefixes, pressure and temperature entries are preparation for that route rather than part of it. They put the numbers into the units the relationships expect before any chemistry starts, which is why they belong at the top of a page of working rather than in the middle.

If a problem stalls, ask which of the four arrows you are on, then whether the units on that line cancel. A no to the second means a factor went in upside down. What a chart cannot do is answer the first question, and that is the gap Flasky fills: it names the conversion a problem needs and the condition attached to it before it substitutes anything. A number on its own never tells you which arrow you were on.

Every relationship named here has a page with its variables, its conditions and a worked example, collected at chemistry formulas, and the formula sheet by topic groups them in the order a course reaches them.

Sources